wickensonline.co.uk -> VAXEN-> DS10L

AlphaServer DS10L

This is a log of the information generated during boot of the DS10L. The DS10L is a 1-U rackmount alpha box designed to run OpenVMS. It has a management computer enabling it to be controlled via an onboard serial port. The remote management computer allows the box to be powered on and off remotely.

The example below is for OpenVMS 7.3. If you scroll down there is a transcript of the commands required to create ISO images of the OpenVMS 8.3 operating system disk and utility disks using the LD virtual disk driver.

>>>show config
                        AlphaServer DS10L 466 MHz

SRM Console:    V6.7-1
PALcode:        OpenVMS PALcode V1.98-83, Tru64 UNIX PALcode V1.92-73

Processors
CPU 0           Alpha EV6 pass 2.3 466 MHz
                SROM Revision: V1.14.208
                Bcache size: 2 MB

Core Logic
Cchip           DECchip 21272-CA Rev 2
Dchip           DECchip 21272-DA Rev 2
Pchip 0         DECchip 21272-EA Rev 2

TIG             Rev 2.1
Arbiter         Rev 7.30 (0xfe)

MEMORY

Array #       Size     Base Addr
-------    ----------  ---------
   0         512 MB    000000000

Total Bad Pages = 0
Total Good Memory = 512 MBytes


PCI Hose 00
     Bus 00  Slot 07: Acer Labs M1543C
                                                         Bridge to Bus 1, ISA
     Bus 00  Slot 09: DE500-BA Network Controller
                                   ewa0.0.0.9.0          08-00-2B-87-53-A6
     Bus 00  Slot 11: DE500-BA Network Controller
                                   ewb0.0.0.11.0         08-00-2B-87-53-BC
     Bus 00  Slot 13: Acer Labs M1543C IDE
                                   dqa.0.0.13.0
                                   dqa0.0.0.13.0          Maxtor 6 Y120P0
     Bus 00  Slot 17: 4C571002/10021002



ISA
Slot    Device  Name            Type         Enabled  BaseAddr  IRQ     DMA
0
        0       MOUSE           Embedded        Yes     60      12

        1       KBD             Embedded        Yes     60      1

        2       COM1            Embedded        Yes     3f8     4

        3       COM2            Embedded        Yes     2f8     3

        4       LPT1            Embedded        Yes     3bc     7

        5       FLOPPY          Embedded        Yes     3f0     6       2

>>>boot
Initializing...
*** keyboard not plugged in...
512 Meg of system memory
probing hose 0, PCI
probing PCI-to-ISA bridge, bus 1
bus 0, slot 9 -- ewa -- DE500-BA Network Controller
bus 0, slot 11 -- ewb -- DE500-BA Network Controller
bus 0, slot 13 -- dqa -- Acer Labs M1543C IDE
bus 0, slot 13 -- dqb -- Acer Labs M1543C IDE
initializing GCT/FRU at 1ff42000

ewa0: link up : Negotiated  100BaseTX: full duplex
......
ewb0: link failed : Using  100BaseTX: full duplex
Testing the System
Testing the Disks (read only)
Testing ew* devices.
System Temperature is 45 degrees C

AlphaServer DS10L 466 MHz Console V6.7-1, Apr 23 2004 09:06:14

CPU 0 booting

(boot dqa0.0.0.13.0 -flags 0,0)
block 0 of dqa0.0.0.13.0 is a valid boot block
reading 1031 blocks from dqa0.0.0.13.0
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 80e00(527872)
initializing HWRPB at 2000
initializing page table at 1ff2e000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code


    OpenVMS (TM) Alpha Operating System, Version V7.3-1

%DECnet-I-LOADED, network base image loaded, version = 05.0F.03

%DECnet-W-NOOPEN, could not open SYS$SYSROOT:[SYSEXE]NET$CONFIG.DAT

$!  . Copyright 1976, 2004 Hewlett-Packard Development Company, L.P.
%STDRV-I-STARTUP, OpenVMS startup begun at 12-APR-2007 13:21:34.77
%EWA0, Auto-negotiation mode set by console
%EWB0, Auto-negotiation mode set by console
%EWA0, Auto-negotiation (internal) starting
%EWB0, Auto-negotiation (internal) starting
%EWA0, Full Duplex 100baseTX connection selected
%EWA0, Link state: UP
%RUN-S-PROC_ID, identification of created process is 00000204
%RUN-S-PROC_ID, identification of created process is 00000205
%%%%%%%%%%%  OPCOM  12-APR-2007 13:21:53.56  %%%%%%%%%%%
Operator _NODE2$OPA0: has been enabled, username SYSTEM

%%%%%%%%%%%  OPCOM  12-APR-2007 13:21:53.58  %%%%%%%%%%%
Operator status for operator _NODE2$OPA0:
CENTRAL, PRINTER, TAPES, DISKS, DEVICES, CARDS, NETWORK, CLUSTER, SECURITY,
LICENSE, OPER1, OPER2, OPER3, OPER4, OPER5, OPER6, OPER7, OPER8, OPER9, OPER10,
OPER11, OPER12

%SET-I-NEWAUDSRV, identification of new audit server process is 0000020A
%%%%%%%%%%%  OPCOM  12-APR-2007 13:21:53.70  %%%%%%%%%%%
Logfile has been initialized by operator _NODE2$OPA0:
Logfile is NODE2::SYS$SYSROOT:[SYSMGR]OPERATOR.LOG;57

%%%%%%%%%%%  OPCOM  12-APR-2007 13:21:53.70  %%%%%%%%%%%
Operator status for operator NODE2::SYS$SYSROOT:[SYSMGR]OPERATOR.LOG;57
CENTRAL, PRINTER, TAPES, DISKS, DEVICES, CARDS, NETWORK, CLUSTER, SECURITY,
LICENSE, OPER1, OPER2, OPER3, OPER4, OPER5, OPER6, OPER7, OPER8, OPER9, OPER10,
OPER11, OPER12

%%%%%%%%%%%  OPCOM  12-APR-2007 13:21:53.70  %%%%%%%%%%%
Message from user WBM$SERVER
%WBM-I-WBMINFO Write Bitmap has successfully completed initialization.

%%%%%%%%%%%  OPCOM  12-APR-2007 13:21:54.33  %%%%%%%%%%%
Message from user SYSTEM on NODE2
%JBC-E-OPENERR, error opening SYS$COMMON:[SYSEXE]QMAN$MASTER.DAT;

%%%%%%%%%%%  OPCOM  12-APR-2007 13:21:54.33  %%%%%%%%%%%
Message from user SYSTEM on NODE2
-RMS-E-FNF, file not found

%%%%%%%%%%%  OPCOM  12-APR-2007 13:21:55.59  %%%%%%%%%%%
Message from user SYSTEM on NODE2
%ACME-I-SERVERSTART, ACME_SERVER starting

%%%%%%%%%%%  OPCOM  12-APR-2007 13:21:56.45  %%%%%%%%%%%
Message from user SYSTEM on NODE2
%SECSRV-E-NOPROXYDB, cannot find proxy database file NET$PROXY.DAT
%RMS-E-FNF, file not found

%%%%%%%%%%%  OPCOM  12-APR-2007 13:21:56.49  %%%%%%%%%%%
Message from user SYSTEM on NODE2
%SECSRV-E-NOPROXYDB, cannot find proxy database file NET$PROXY.DAT
%RMS-E-FNF, file not found

%%%%%%%%%%%  OPCOM  12-APR-2007 13:21:56.49  %%%%%%%%%%%
Message from user SYSTEM on NODE2
%SECSRV-I-CIACRECLUDB, security server created cluster intrusion database

%%%%%%%%%%%  OPCOM  12-APR-2007 13:21:56.49  %%%%%%%%%%%
Message from user SYSTEM on NODE2
%SECSRV-I-SERVERSTARTINGU, security server starting up

%%%%%%%%%%%  OPCOM  12-APR-2007 13:21:56.63  %%%%%%%%%%%
Message from user SYSTEM on NODE2
%SECSRV-I-CIASTARTINGUP, breakin detection and evasion processing now starting u
p

Copyright 2003 Hewlett-Packard Development Company, L.P.
%NET$STARTUP-W-NONETCONFIG, this node has not been configured to run DECnet-Plus
 for OpenVMS
        use SYS$MANAGER:NET$CONFIGURE.COM if you wish to configure DECnet
%NET$STARTUP-I-OPERSTATUS, DECnet-Plus for OpenVMS operational status is OFF
%DECdtm-F-NODECnet, the TP_SERVER process was not started because either:

o  DECnet-Plus is not started or is not configured, or

o  The SYS$NODE_FULLNAME logical name is not defined

   This could be because when you installed DECnet-Plus and were prompted
   for the system's full name, you specified a local name instead of a
   DECdns or Domain name.

If you want to use DECdtm services, make sure that DECnet-Plus is started and
configured and that SYS$NODE_FULLNAME is defined, then use the following
command to start the TP_SERVER process:

    $ @SYS$STARTUP:DECDTM$STARTUP.COM

%STARTUP-I-AUDITCONTINUE, audit server initialization complete
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:09.19  %%%%%%%%%%%
Message from user AUDIT$SERVER on NODE2
Security alarm (SECURITY) and security audit (SECURITY) on NODE2, system id: 102
6
Auditable event:          Audit server starting up
Event time:               12-APR-2007 13:22:09.06
PID:                      00000203
Username:                 SYSTEM


The OpenVMS Alpha system is now executing the site-specific startup commands.

%RUN-S-PROC_ID, identification of created process is 00000210
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:10.00  %%%%%%%%%%%
Message from user SYSTEM on NODE2
%SMHANDLER-S-STARTUP, server management event handler startup


%TCPIP-I-INFO, TCP/IP Services startup beginning at 12-APR-2007 13:22:10.91
%TCPIP-I-NORMAL, timezone information verified
%RUN-S-PROC_ID, identification of created process is 00000211
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:12.47  %%%%%%%%%%%
Message from user INTERnet on NODE2
INTERnet Loaded

%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:12.51  %%%%%%%%%%%
Message from user INTERnet on NODE2
Subsystem "inet" configured by process 00010011
Status: success

%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:12.51  %%%%%%%%%%%
Message from user INTERnet on NODE2
Subsystem "net" configured by process 00010011
Status: success

%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:12.51  %%%%%%%%%%%
Message from user INTERnet on NODE2
Subsystem "socket" configured by process 00010011
Status: success

%TCPIP-I-SETLOCAL, setting domain and/or local host
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:12.51  %%%%%%%%%%%
Message from user INTERnet on NODE2
Subsystem "iptunnel" configured by process 00010011
Status: success

%TCPIP-I-STARTCOMM, starting communication
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:12.51  %%%%%%%%%%%
Message from user INTERnet on NODE2
Subsystem "ipv6" configured by process 00010011
Status: success

%TCPIP-I-SETPROTP, setting protocol parameters
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:12.51  %%%%%%%%%%%
Message from user INTERnet on NODE2
Subsystem "snmpinfo" configured by process 00010011
Status: success

%TCPIP-I-DEFINTE, defining interfaces
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:13.46  %%%%%%%%%%%
Message from user INTERnet on NODE2
INTERnet Started

%TCPIP-I-STARTNAME, starting name service
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:14.00  %%%%%%%%%%%
Message from user INTERnet on NODE2
INTERnet ACP Created INTERnet interface: WE0

%TCPIP-I-STARTDROUT, starting dynamic routing
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:14.01  %%%%%%%%%%%
Message from user INTERnet on NODE2
INTERnet ACP Created INTERnet interface: WE1

%EWA0, Auto-negotiation (internal) starting
%EWA0, Link state: DOWN
%EWA0, Full Duplex 100baseTX connection selected
%EWA0, Link state: UP
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:19.53  %%%%%%%%%%%
Message from user Proxy Server on NODE2
Loading proxy server image TCPIP$PROXY_SERVICES

%TCPIP-S-STARTDONE, TCP/IP Kernel startup completed
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:19.54  %%%%%%%%%%%
Message from user INTERnet on NODE2
Subsystem "proxy" configured by process 00010003
Status: success

%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:20.65  %%%%%%%%%%%
Message from user INTERnet on NODE2
INTERnet ACP Activate BIND Server

%TCPIP-S-STARTDONE, TCPIP$BIND startup completed
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:20.66  %%%%%%%%%%%
Message from user INTERnet on NODE2
INTERnet ACP NOLISTEN Process creation success: Service - BIND

%TCPIP-I-PROXYLOADED, loaded 0 NFS proxy records
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:20.66  %%%%%%%%%%%
Message from user INTERnet on NODE2
INTERnet ACP Activate BIND Server

%TCPIP-I-LOADSERV, loading TCPIP server proxy information
%TCPIP-I-SERVLOADED, auxiliary server loaded with 0 proxy records
-TCPIP-I-SERVSKIP, skipped 0 communication proxy records
-TCPIP-I-SERVTOTAL, total of 0 proxy records read
%TCPIP-S-STARTDONE, TCPIP$PROXY startup completed
%TCPIP-S-STARTDONE, TCPIP$DHCP_CLIENT startup completed
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:21.66  %%%%%%%%%%%
Message from user INTERnet on NODE2
INTERnet ACP Error during process startup, Nolisten Service Disabled - BIND Serv
er

%TCPIP-S-STARTDONE, TCPIP$FTP startup completed
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:21.66  %%%%%%%%%%%
Message from user INTERnet on NODE2
INTERnet ACP Deactivate BIND Server

%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:21.84  %%%%%%%%%%%
Message from user INTERnet on NODE2
INTERnet ACP Activate FTP Server

%TCPIP-S-STARTDONE, TCPIP$FTP_CLIENT startup completed
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:21.84  %%%%%%%%%%%
Message from user INTERnet on NODE2
INTERnet ACP NOLISTEN Process creation success: Service - FTP

%TCPIP-S-STARTDONE, TCPIP$TELNET startup completed
%%%%%%%%%%%  OPCOM  12-APR-2007 13:22:22.48  %%%%%%%%%%%
Message from user INTERnet on NODE2
INTERnet ACP Activate TELNET Server

%TCPIP-S-STARTDONE, TCP/IP Services startup completed at 12-APR-2007 13:22:22.63

%SET-I-INTSET, login interactive limit = 64, current interactive value = 0
%DECW$DEVICE-I-NODEVICE, no graphics devices found.
Number of screens:         0
Screen devices and order:  NONE
  SYSTEM       job terminated at 12-APR-2007 13:22:29.42

  Accounting information:
  Buffered I/O count:               4316      Peak working set size:       7184
  Direct I/O count:                 3768      Peak virtual size:         183184
  Page faults:                      6335      Mounted volumes:                0
  Charged CPU time:        0 00:00:03.64      Elapsed time:       0 00:00:55.22

 Welcome to OpenVMS (TM) Alpha Operating System, Version V7.3-1

Username: system
Password:
   Welcome to OpenVMS (TM) Alpha Operating System, Version V7.3-1
    Last interactive login on Monday,  9-APR-2007 15:58:55.78
    Last non-interactive login on Thursday, 29-MAR-2007 20:35:45.62
$ 

Create Boot Disk CDROM Images

$ ld create alpha083.dsk/size=1180896
$ ld connect alpha083.dsk lda1:
$ init lda1: cdrom/clus=1
$ mount/noassist/foreign lda1: cdrom
%MOUNT-I-MOUNTED, CDROM mounted on _NODE2$LDA1:
$ backup/init/image dqa0:[msw]alpha083.bck/save_set lda1:
$ dismount lda1
$ mount/noassist lda1: alpha083
%MOUNT-I-MOUNTED, ALPHA083 mounted on _NODE2$LDA1:
$ dir lda1:[000000]

Directory LDA1:[000000]

000000.DIR;1        ALPHA083.DIR;1      AVAIL_MAN_BASE.DIR;1
BACKUP.SYS;1        BADBLK.SYS;1        BADLOG.SYS;1        BITMAP.SYS;1
CDSA_ALPHA022.DIR;1 CLEAN_SDA_HELP.COM;1                    CONTIN.SYS;1
CORIMG.SYS;1        DECNET_PHASE_IV_ALPHA083.DIR;1
DECNET_PLUS_ALPHA083.DIR;1              DWMOTIF_ALPHA016.DIR;1
DWMOTIF_SUPPORT_ALPHA083.DIR;1          INDEXF.SYS;1        ISL_SCRIPT.ESS;1
KERBEROS_ALPHA030.DIR;1                 KITS.DIR;1          SECURITY.SYS;1
SSL_ALPHA013.DIR;1  SYS0.DIR;1          SYS1.DIR;1          SYS10.DIR;1
SY

$ dismount/nounload lda1:
$ ld disconnect lda1:

$ ld create alp083lp1.dsk/size=398112
$ ld connect alp083lp1.dsk lda1:
$ init lda1: cdrom/clus=1
$ mount/noassist/foreign lda1: cdrom
%MOUNT-I-MOUNTED, CDROM mounted on _NODE2$LDA1:
$ backup/init/image dqa0:[msw]alp083lp1.bck/save_set lda1:
$ dismount lda1
$ mount/noassist lda1: alp083lp1
%MOUNT-I-MOUNTED, ALP083LP1 mounted on _NODE2$LDA1:
$ dir lda1:[000000]

Directory LDA1:[000000]

000000.DIR;1        AVAILMAN_ALPHA026.DIR;1                 BACKUP.SYS;1
BADBLK.SYS;1        BADLOG.SYS;1        BITMAP.SYS;1        CONTIN.SYS;1
CORIMG.SYS;1        DCPS_025.DIR;1      DEBUG_CLIENTS011.DIR;1
DECDFS_024A.DIR;1   ECP_056A.DIR;1      GWLM_ALPHA0113.DIR;1
INDEXF.SYS;1        KITS.DIR;1          MGMTAGENTS_ALPHA034.DIR;1
RAID_030A.DIR;1     SECURITY.SYS;1      TIMEZONE.DIR;1
VMSI18N_ALPHA083.DIR;1                  VOLSET.SYS;1

Total of 21 files.
$ dismount/nounload lda1:
$ ld disconnect lda1:
$                 

$ ld create ebizcdv21_1of2.dsk/size=1094880
$ ld connect ebizcdv21_1of2.dsk  lda1:
$ init lda1: cdrom/clus=1
$ @reset_backup_saveset_attributes ebizcdv21_1of2.bck;
$ @reset_backup_saveset_attributes ebizcdv21_2of2.bck;

$ mount/noassist lda1: cdrom
$ set def lda1:[000000]
$ backup dqa0:[msw]ebizcdv21_1of2.bck/save_set lda1:[000000...]
$ dismount/nounload lda1:
$ ld disconnect lda1:

$ ld create ebizcdv21_2of2.dsk/size=1070400
$ ld connect ebizcdv21_2of2.dsk lda1:
$ init lda1: cdrom/clus=1
$ mount/noassist lda1: cdrom
%MOUNT-I-MOUNTED, CDROM mounted on _NODE2$LDA1:
$ set def lda1:[000000]
$ backup/verify dqa0:[msw]ebizcdv21_2of2.bck/save_set lda1:[000000...]/list
$ dismount/nounload lda1:
$ ld disconnect lda1:

$ @reset_backup_saveset_attributes opnsrctools4.bck;
$ dismount/nounload lda1:
$ ld disconnect lda1:
$ del opensrctools4.dsk;
$ ld create opnsrctools4.dsk/size=605280
$ ld connect opnsrctools4.dsk lda1:
$ init lda1: cdrom/clus=1
$ mount/noassist lda1: cdrom
%MOUNT-I-MOUNTED, CDROM mounted on _NODE2$LDA1:
$ backup/verify opnsrctools4.bck/save_set lda1:[000000...]
%BACKUP-E-OPENOUT, error opening LDA1:[000000.000000]SECURITY.SYS;1 as output
-RMS-E-FEX, file already exists, not superseded
%BACKUP-I-STARTVERIFY, starting verification pass
%BACKUP-E-VERIFYERR, verification error for block 1 of LDA1:[000000.000000]SECUR
ITY.SYS;1
$ dir lda1:[000000]

Directory LDA1:[000000]

000000.DIR;1        000TOOLS.DIR;1      BACKUP.SYS;1        BADBLK.SYS;1
BADLOG.SYS;1        BITMAP.SYS;1        CDRECORD_SOURCE.DIR;1
CDSA_SOURCE.DIR;1   CONTIN.SYS;1        CORIMG.SYS;1        GNUPG.DIR;1
GNV.DIR;1           GNV_I64.DIR;1       GTK.DIR;1           IAS.DIR;1
INDEXF.SYS;1        KERBEROS_SOURCE.DIR;1                   KITS.DIR;1
LIBIDL.DIR;1        README.TXT;1        SECURITY.SYS;1      SSL_SOURCE.DIR;1
STUNNEL.DIR;1       VOLSET.SYS;1

Total of 24 files.
$ dismount/nounload lda1:
$ ld disconnect lda1:
$ dir/size *.dsk

Directory DQA0:[MSW]

ALP083LP1.DSK;1       398112
ALPHA083.DSK;1       1180896
EBIZCDV21_1OF2.DSK;1
                     1094880
EBIZCDV21_2OF2.DSK;1
                     1070400
OPNSRCTOOLS4.DSK;1    605280

Total of 5 files, 4349568 blocks.
$